manualshive.com logo in svg

FLENDER K.A Series, Руководство по эксплуатации

Поделиться
Скачать
FLENDER K.A Series Скачать руководство пользователя страница 31

Note
Observe the flow direction of the pump
When connecting the valves, observe the flow direction of the pump.
Refer to the pump operating instructions in the complete gear unit documentation to ascertain 

whether the flow direction of the pump used depends on the direction of rotation.

Improper use can damage the gear unit. Follow the instructions given below in order to protect 

the gear unit against overheating:
● When installing a gear unit with mounted air-oil cooler, carefully ensure that air can freely 

circulate.

The necessary minimum clearance to adjacent components such as walls and panels is 

specified in the dimension drawing in the complete gear unit documentation.

● Please note that the cooling effect is considerably reduced as a result of a dirty air-oil cooler 

or the insulating effect of dirt or pollution on the housing surface.

Clean the air-oil cooler and the gear unit. Cleaning information is provided in 

chapter Cleaning the fan and gear unit (Page 93).

Further information

Additional information such as connection dimensions and a detailed illustrated description of 

the gear unit and the oil supply system with air-oil cooler can be found in the dimension drawing 

in the complete gear unit documentation.
Additional information about the oil supply system and control notes can be found in the 

separate data sheet, in the list of equipment and in the oil supply system operating instructions 

provided in the complete gear unit documentation.

Temperature control valve

A temperature control valve is installed in the air-oil cooler bypass.

Principle of operation

At a preset temperature, the temperature control valve starts to open and some oil flows 

through the oil cooler; when a second preset temperature is reached, then all of the oil flows 

through the oil cooler.

Further information

You can find additional information on the temperature control valve in the temperature control 

valve operating instructions provided in the complete gear unit documentation.
You can find additional technical data in the separate data sheet and in the list of equipment 

provided in the complete gear unit documentation.

Description

3.7 Cooling

REDUREX Gear unit  5200en

Operating Instructions 03/2019

31

Содержание K.A Series

































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды