FLENDER K.A Series Скачать руководство пользователя

Страница: 98 / 128

4. If you discover that there are heavy deposits inside the cooling coil, arrange for the cooling

water or the deposits to be analysed.

Analysis services of this kind are offered by specialist chemical cleaning companies. These

companies also sell special cleaning agents for removing deposits. Before you use a

cleaning agent, check whether it is suitable for use on the cooling coil materials. You must

consult Flender Customer Services. Carefully read the instructions for use supplied by the

manufacturer before using different kinds of cleaning agent.

5. If the cooling coil is severely soiled, it must be replaced by a new one.

Please consult Flender Customer Services for further advice.

6. Reconnect the cooling water inlet and drain lines to the cooling coil.

8.3.11

Inspecting the shrink disk

Introduction

The shrink disk inspection is limited to a visual assessment of its condition.

Aspects of the inspection

Observe the following points when inspecting the shrink disk:
● Loose bolts
● Damage due to use of force
● Inner ring resting flush against the outer ring

Further information

Further information about the shrink disk can be found in the shrink disk operating instructions

in the complete documentation for the gear unit.

8.3.12

Check that all of the fastening bolts are tight

Procedure

Proceed as follows to check that the fastening bolts are tight:
1. Observe the data regarding connection classes (Page 78), preload forces and tightening

torques (Page 79).

2. Replace any bolts that are no longer fit for use by bolts of the same strength class and type.

Maintenance
8.3 Maintenance and service work

REDUREX Gear unit 5200en

Operating Instructions 03/2019

Содержание K.A Series

































































































































Результаты поиска

Содержание K.A Series

Отзывы:

Похожие инструкции для K.A Series

Бренды по названию

Популярные бренды

FLENDER K.A Series, Руководство по эксплуатации

Результаты поиска

Содержание K.A Series

Отзывы:

Похожие инструкции для K.A Series

Бренды по названию

Популярные бренды