manualshive.com logo in svg

FlavorShot AC-FS5, Руководство по обслуживанию

Поделиться
Скачать
FlavorShot AC-FS5 Скачать руководство пользователя страница 49

 

49

      advance,  contact the A.C. Dispensing Equipment    
      Inc. Technical Assistance Center at 1-888-777-9990 
      or 1-902-865-9602.  
  9. Check to ensure that the LCD Display shows “Select
      flavor”.  
      If the LCD is not on, check the circuit breaker: 
      Confirm that the Circuit Breaker on the lower left 
      side of the dispenser has not tripped out. If it has, 
      turn OFF the dispenser, re-set the circuit breaker by  
      gently pushing it in once to reset it  – push in at the   
      top of the breaker until no white is showing.  Then,  
      turn the power back ON.  
10. Read the LCD window to see if the dispenser is 
      indicating action required, such as filling the tank.      
11. If there still is no product dispensed, contact the A.  
      C. Dispensing Equipment Inc. Technical Assistance  
      Center at 1-888-777-9990 or 1-902-865-9602.  
 

 
Dispenser is  
not dispensing the  
proper amounts of  
product  
 

 
1.  Make sure the flavor delivery tubes are inserted in   
     the product dispensing block correctly since kinks or 
     blockages can affect delivery amounts.   
2.  Check to ensure that the product dispensing block is 
     clean. 
3.  Product may have run dry before refilling. Complete 
     a prime cycle.  (See Step 9, page 9) 
4.  Inlet check valve in the pump body below the tank 
     spout may be bypassing and need to be replaced.   
     Replacement check valves are available from A. C. 
     Dispensing Equipment Inc. Technical Assistance 
     Center at 1-888-777-9990 or 1-902-865-9602. 
5.  Check filter washer and clean as necessary. 
     
To replace inlet check valve:  

a.  Empty flavor tank by pressing and holding the 

Clean button for two seconds and allowing the 
flavor to drain out. 

b.  Lift flavor tank out. 
c.  Loosen the plastic check valve retainer with a 

wrench and unscrew to remove. 

d.  Remove the filter washer and inlet check valve.
e.  Replace with a new inlet check valve. Ensure 

correct placement of the valve:  inlet at the top 
facing the tank and outlet at the bottom toward 
the valve block.  (See page 39) 

f.  Replace the filter washer. 
g.  Tighten the retainer until it is snug. Do not 

over-tighten.  

Содержание AC-FS5

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды