manualshive.com logo in svg

FlavorShot AC-FS5, Руководство по обслуживанию

Поделиться
Скачать
FlavorShot AC-FS5 Скачать руководство пользователя страница 15

 

15

7.  LCD DISPLAYS

 

 
The Liquid Crystal Display (LCD) at the top left of the Button Panel (See page 
12) on the front of the dispenser shows the current dispenser function.  

Press a button to Select Product.  The LCD shows the operational status of that  
flavor tank: 
 

 

Display 

 

Message 

 

Select Flavor 

indicates dispenser ready for a flavor selection 

Flavor 1, 2, 3, 4, 5           indicates flavor selected 

Modifier 1, 2, 3, 4, 5 

indicates the Modifier selected  

Top Up          (X) 
Small             (S) 
Medium         (M)    
Large             (L)      
Extra-Large   (XL) 

indicates size selected 
 
 

Refill Tank 

Indicates tank must be filled to the “Full” line 

Reset – Full 

indicates tank level is resetting to “Full” 

Reset - Low Fill 

Indicates tank level is resetting to “Low Fill” quantity 

Prime 

indicates tank priming 

Clean 

indicates tank cleaning underway 

Panel Disabled 

Indicates the Button Panel is disabled – no product will be 
dispensed 

IR 

Indicates dispenser is being reprogrammed and the download 
of the new program is underway  

Program Mode: 1 
 

indicates dispenser is in Program Mode and the Size, Flavor, 
and Modifier buttons may be used to adjust delivery amounts      

Program Mode: 2 

This Mode is for factory settings only.  
Press Clean button again to return to Program Mode: 1  OR  
contact A. C. Dispensing Equipment Inc Technical Assistance 
Center at 1-888-777-9990 or 1-902-865-9602 

Wait 

appears as dispenser powers up 

 
NOTES:  

•

  Once the flavor is dispensed, the LCD cycles back to Select Flavor.  

•

  Display returns to normal operating conditions after 3 seconds. 

 

Содержание AC-FS5

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды