manualshive.com logo in svg

FlavorShot AC-FS5, Руководство по обслуживанию

Поделиться
Скачать
FlavorShot AC-FS5 Скачать руководство пользователя страница 20

 

20

CLEANING:  Product Dispensing Block and surrounding area 

•

  The area around the product dispensing block must be kept clean for 

proper sanitation.   

•

  The area around the product dispensing block should be brushed with a 

sanitized brush and wiped clean daily with a clean, sanitized towel. 

 

•

  Cleaning the Product Dispensing Block may introduce small air bubbles 

into the dispense tube. This does not affect dispense amounts. 
Periodically, prime the pump to remove this air bubble. 

 

 
 
 
 
 

CLEANING SCHEDULE  

Daily

 

-  wipe the dispenser exterior with a clean, sanitized towel  
-  clean product dispensing block: brush with a sanitized brush and 

         wipe clean with a clean, sanitized towel    

-  clean catch tray: rinse, wash, rinse, sanitize, and air dry 

 
Every 30 days

 -  clean all flavor tanks, caps, and pumps, using the  

                         

   procedures above  

                          -  clean check valves   Check valves are automatically 
                            cleaned during tank cleaning. Disassemble only if problem 
                            suspected.        

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Содержание AC-FS5

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды