manualshive.com logo in svg

FlavorShot AC-FS5, Руководство по обслуживанию

Поделиться
Скачать
FlavorShot AC-FS5 Скачать руководство пользователя страница 25

 

25

5.  “ON/OFF” switch and Circuit Breaker removal 

 

 
To Remove and Replace the ON/OFF Switch (Power Switch): 
1.  Disconnect the AC power supply. 
2.  Remove the lower front panel by removing its 4 screws. 
3.  Disconnect the 2 power wires to the switch.  Note their positions.  
4.  From inside the dispenser, pinch the top and bottom of the Power Switch 
     retainers. 
5.  Push the switch out of the dispenser. 
6.  Insert new power switch.  Make sure the ON part of the rocker switch is at the 
     top. 
7.  Reconnect the wires, restoring the wires to their previous positions.  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

  

To Remove and Replace the Circuit Breaker:           
1.  Disconnect the AC power supply. 
2.  Remove the lower front panel by removing its 4 screws. 
3.  Disconnect the 2 power wires to the switch.  Note their positions.  
4.  From inside the dispenser, depress the Circuit Breaker retainers on the left 
     and right sides. 
5.  Push the Circuit Breaker out of the dispenser. 
6.  Insert new Circuit Breaker.  Confirm the top-bottom orientation by checking    
     the printing on the outside of the Circuit Breaker.  
7.  Reconnect the wires, restoring the wires to their previous positions.  

 
 
 

Содержание AC-FS5

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды