manualshive.com logo in svg

Flavor Burst FB 80INT-08, Руководство пользователя

Поделиться
Скачать
Flavor Burst FB 80INT-08 Скачать руководство пользователя страница 53

 

52

Assembling the Injector Assembly

 

 
1.  Place the Gear Cartridge into the Drive 

Assembly Gear Box so that the gear teeth 
line up with the gear inside the Drive 
Assembly Gear Box.  (See Figure 129.)   

 

26023

 

Figure 129

 

 
2.  Install the Injector Head onto the Drive 

Assembly Gear Box and rotate off-center to 
secure.  (See Figure 130.)   

 

26024

 

Figure 130

 

 
3.  Insert the Drive Motor into the Drive 

Assembly Gear Box so that all four locking 
screws are seated properly and rotate the 
motor clockwise to secure.  (See          
Figure 131.)   

 

26025

 

Figure 131

 

 
 

Installing the Injector System and 
Suspension Bracket 

 
The Suspension Bracket helps stabilize the 
Injector Assembly on the freezer.  When 
properly installed on the freezer, the Bracket 
should hold the Injector Assembly level 
horizontally, with the Injector Head lined up 
directly under the Spout Adapter.  The 
Suspension Bracket is adjustable to fit many 
common freezer models.  Additional 
Suspension Bracket styles are available for use 
with other freezer models.  Contact your local 
distributor for more information. 
 
The Injector Assembly can be mounted to either 
side of the freezer spout. The 9-Tube Assembly 
may also come from either side, regardless of 
the Injector Assembly’s position.  However it is 
highly recommended the Injector Assembly is 
installed so that the 9-Tube Assembly wraps 
around the side of the freezer with the intake 
vents (typically on the left side) and not the 
outtake vent (typically on the right side).  This is 
because the outtake vent could warm the syrup 
in the tubes and therefore warm the frozen 
product as it is served.  Installing the tubes on 
the side of the intake vents keeps the syrup 
cool and the product consistent.  
 
The following instructions and illustrations show 
a left-side mounting, which is recommended for 
Taylor C707 / C708 freezer.  In cases where 
left-side mounting is not possible, the Injector 
Assembly and tubes may be installed on the 
other side. 

 

 
1.  Determine which side of the freezer the 

Injector Assembly will be mounted on.  The 
Suspension Bracket should be installed to 
the outside of the Gear Box Assembly.  
(See Figure 132.) 

 

26047

 

Figure 132 

 

Содержание FB 80INT-08






















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды