manualshive.com logo in svg

Flavor Burst FB 80INT-08, Руководство пользователя

Поделиться
Скачать
Flavor Burst FB 80INT-08 Скачать руководство пользователя страница 49

 

48

 

NOTE: 

YOUR HANDS SHOULD BE CLEANED 

AND SANITIZED BEFORE YOU PERFORM 
THE FOLLOWING PROCEDURES. 
 

NOTE:  

INSPECT ALL WEAR ITEMS AND 

REPLACE IF NECESSARY. 
 

NOTE:  

THE FOLLOWING PROCEDURES 

REQUIRE APPROVED, SERVICEABLE AND 
SANITIZED TOOLS AND BRUSHES.  
CONTACT YOUR LOCAL DISTRIBUTOR FOR 
RECOMMENDED SUPPLIES. 
 

NOTE:

  USE AN APPROVED CLEANER AND 

SANITIZER FOR THE FOLLOWING 
PROCEDURES.  REFER TO 
MANUFACTURER’S INSTRUCTIONS FOR 
PROPER PREPARATIONS OF THESE 
CLEANING AGENTS. 
 
 

Installing the Spout Adapter 

 
Every FB 80INT system ships with an        
ADPT 101A standard Adapter common to    
most freezers and an ADPT 8750A alternate 
Adapter for use with most Taylor Crown Series 
freezers. However, if neither Adapter fits the 
freezer spout, additional Adapters are available 
from your local distributor for use with other 
models and freezer manufacturers. See the 
ALTERNATE PARTS AND KITS BY FREEZER 
MODEL section for more information.

   

 

Since the fitting is very tight, install the Adapter 
with the freezer door removed.  Keep 
replacement o-rings and gasket in the Spare 
Parts Kit. 
 

NOTE: 

 THE ADPT 8750A ADAPTER DOES 

NOT INCLUDE A GASKET.  IGNORE 
REFERENCES TO THE GASKET IF THIS 
ADAPTER IS INSTALLED.

 

 

1.  Ensure that the Spout Adapter has been 

sanitized according to instructions in the 
SCHEDULED MAINTENANCE section.  
Then lube and install the white gasket and 
both o-rings in their proper places inside 
and outside of the Spout Adapter. (See 
Figure 114.)   

 

 

Figure 114 

 

2.  Clean the freezer door and spout according 

to manufacturer’s instructions before 
installing the Spout Adapter on the freezer 
door.   

 
3.  Set the Adapter on a flat, clean surface, and 

then place the freezer door spout upright 
onto the Adapter.  Rock the freezer door 
forward to snap the Adapter into place.  
(See Figure 115.)   

 

 

Figure 115

 

 

4.  Return the door to the freezer with the 

Spout Adapter attached. 

 
 

EQUIPMENT SETUP 

Содержание FB 80INT-08






















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды