manualshive.com logo in svg

Flavor Burst FB 80INT-08, Руководство пользователя

Поделиться
Скачать
Flavor Burst FB 80INT-08 Скачать руководство пользователя страница 1

©2011 Flavor Burst Company                                                          Printed in April       

   

 

Printed in  

All Rights Reserved 

   

                               The United States of America

 

Flavor Burst

 ®

  

Soft Serve System 
Model FB 80INT-08 
Model FB 80INT-26 

 

 
Manufactured by 
 
Flavor Burst Company 
499 Commerce Drive 
Danville, IN  46122 
 
For general information and to locate a 
distributor near you, call or visit our 
website: 
Phone:  (317) 745-2952 
Toll Free Number: (800) 264-3528 
Fax:  (317) 745-2377 

www.flavorburst.com

 

 
For pricing, ordering and support, contact 
one of our qualified distributors. 
 
 

 

 
 

Warranty 

 

An installation and warranty form is provided with every FB 80INT system, located inside the  
FB 80INT unit with this manual.  It is important that the operator carefully review the warranty and 
installation documents accompanying the unit before using this system.  Any questions or concerns 
regarding the warranty should be clarified upon delivery or installation.  For more information, contact 
your local authorized Flavor Burst

 

®

 distributor.

 

Содержание FB 80INT-08






















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды