manualshive.com logo in svg

Fire-Lite Alarms UDACT-F, Инструкция по установке, эксплуатации и программированию

Поделиться
Скачать
Fire-Lite Alarms UDACT-F Скачать руководство пользователя страница 36

36

  Document # 50049  Rev D   5/2/97  P/N 50049:D

                        4.0 Operating Instructions

The UDACT-F has five Modes of operation; Normal, Type Mode, Program, Lamp
Test, and Troubleshoot. Upon initial power up, the system will be in Normal Mode.
This section discusses operation of the UDACT-F in the Normal Mode.

 

4.1.1  Keys

: Below is a description of the function keys in Normal Mode:

The Clear function will cause the UDACT-F to:

• cease transmissions
• clear any active or pending transmissions
• reset and return to normal system processing

To perform the Clear function, press the Clear Key followed by 2, 5, 3, 2, then press
the [ENTER/STORE] key.

If the Test Key is pressed three times in rapid succession the UDACT-F will transmit
a test message to both Central Stations.  The message reported is the same as the
automatic test message for all formats except Ademco Contact ID.

Pressing the Mode Key followed by a valid 4-digit numerical code and [ENTER/

STORE] selects one of the four modes of operation.

☛

To enter normal mode from any other mode press 

MODE

 

then

6676

 

[ENTER/STORE]

.

 6676

 

spells NORM on a

Touch-Tone® phone.

CLEAR

4.1        Normal Mode

TEST

MODE

Technical Manuals Online! - http://www.tech-man.com

firealarmresources.com

Содержание UDACT-F

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды