manualshive.com logo in svg

Fire-Lite Alarms UDACT-F, Инструкция по установке, эксплуатации и программированию

Поделиться
Скачать
Fire-Lite Alarms UDACT-F Скачать руководство пользователя страница 21

21

Document # 50049  Rev D   5/2/97  P/N 50049:D

Telephone Circuits
Provision to connect to two independent telephone lines is available via two
telephone jacks labeled PH1 (Primary) and PH2 (Secondary). Telephone line control/
command is possible via double line seizure as well as usage of an RJ31X style
interconnection.  (RJ31X jacks must be ordered separately).
Note: It is critical that the UDACT-F be located as the first device on the incoming
telephone circuit to properly function.

Note: Shorting bars
inside RJ31X Jack
removed during male
plug insertion

Secondary
Phone Line
PH-2

Primary
Phone Line
PH-1

7 foot
Cable
(MCBL-7)

Order Separately

Male Plug
Connectors

Modular Female
Connectors

(Primary Lines)
Incoming Telco
Phone Lines

Ring

Tip

Tip

Ring

Green Wire

Green Wire

(Secondary Lines)
Incoming Telco
Phone Lines

Red Wire

Red Wire

To premise phones

To premise phones

Tip

Ring

Ring

Tip

Figure  2-8: Wiring Phone Jacks

2.4     Output Circuits

Technical Manuals Online! - http://www.tech-man.com

firealarmresources.com

Содержание UDACT-F

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды