Fire-Lite Alarms UDACT-F Скачать руководство пользователя страница 35

Страница: 35 / 56

Document # 50049 Rev D 5/2/97 P/N 50049:D

Ademco Contact ID Format

If 'E' is entered for address 42, the following data is automatically programmed for the Secondary
phone number event codes.

Enter a '000' for the data setting to disable the report.

Address

Description

Setting

Sensor Number

139 - 141

Secondary # General Alarm Code

110

000

142 - 144

Secondary # Zone/Point Alarm Code

110

Note

145 - 147

Secondary # General Supervisory Code

200

000

148 - 150

Secondary # Zone/Point Supervisory Code

200

Note

151 - 153

Secondary # General Fault Code

300

154 - 156

Secondary # AC Fault Code

301

157 - 159

Secondary # Zone/Point Fault Code

380

Note

160 - 162

Secondary # Low Battery Fault Code

302

163 - 165

Secondary # Telco Primary Line Fault Code

351

166 - 168

Secondary # Telco Secondary Line Fault Code

352

169 - 171

Secondary # NAC Fault Code

321

172 - 174

Secondary # Comm. Trouble Primary # Code

354

175 - 177

Secondary # Comm. Trouble Secondary # Code

354

178 - 180

Secondary # 485 Comm. Trouble Code

300

181 - 183

Secondary # System Off Normal Code

308

184 - 186

Secondary # UDACT-F Off Normal Code

350

187 - 189

Secondary # System 24 Hour Test

602

190 - 192

Secondary # System 24 Hour Test w/active event

608

193 - 195

Secondary # Manual Test Message

601

Notes:

1) Note: Zero entries prevent the transmission of the report to the Central Station.
2) Refer to Contact ID program locations 64 - 68.
3) The identification of the zone/sensor number is automatically transmitted by the UDACT-F and is

added to the main event code. See Appendix A-3 for more information.

4) Factory default for this report is 110 (110 is transmitted for modules, however, 111 will automatically

be transmitted for smoke detectors). Use Type Mode (refer to Section 4.2) to change this report per
zone or point.

Table 3-7: Ademco Contact ID, Secondary Number

Technical Manuals Online! - http://www.tech-man.com

firealarmresources.com

Содержание UDACT-F

























































Результаты поиска

Содержание UDACT-F

Отзывы:

Бренды по названию

Популярные бренды

Fire-Lite Alarms UDACT-F, Инструкция по установке, эксплуатации и программированию

Результаты поиска

Содержание UDACT-F

Отзывы:

Бренды по названию

Популярные бренды