manualshive.com logo in svg

Fire-Lite Alarms UDACT-F, Инструкция по установке, эксплуатации и программированию

Поделиться
Скачать
Fire-Lite Alarms UDACT-F Скачать руководство пользователя страница 16

16

  Document # 50049  Rev D   5/2/97  P/N 50049:D

2.2.2 Sensiscan 2000
Remove all power from the control panel by disconnecting AC and batteries.  Install
the three supplied nylon support posts for the top and bottom left of the UDACT-F,
one aluminum/nylon and one aluminum standoff in the CHS-4 chassis slot in which the
UDACT-F is to be installed (refer to Figure 2-4).  Position the UDACT-F on the standoffs
and secure on aluminum standoff with a #6-32 screw.  Alternatively, the UDACT-F
may be mounted remotely using an ABS-8RF or UBS-1F enclosure.  Ferrite cores are
recommended for this application.  Refer to Figure 2-3 and the accompanying Notes
for wiring alternatives.

Connect the communication line between the EIA-485 terminal block on the CPU-2000
and TB-1 terminals 3 and 4 on the UDACT-F being certain to observe polarity (refer to
Figure 2-5).  Recommended wire is 12 AWG to 18 AWG twisted pair. If no other devices
are connected to the EIA-485, install a 120 ohm EOL resistor across UDACT-F TB1
terminals 3 and 4.

Connect the supplied Ground Strap from the UDACT-F Earth Ground terminal on TB3
to the CHS-4 chassis.  Connect 24VDC filtered, regulated, non-resettable power to TB-
1 terminals 1 and 2 on the UDACT-F (refer to Figure 2-6).

Figure 2-4: UDACT-F Mounting in CHS-4

CPU-2000

UDACT-F

CHS-4

Nylon
Support
Posts

Aluminum Standoff
and screw

Nylon &
Aluminum
Standoff

Ground
Strap

Technical Manuals Online! - http://www.tech-man.com

firealarmresources.com

Содержание UDACT-F

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды