manualshive.com logo in svg

Fire-Lite Alarms UDACT-F, Инструкция по установке, эксплуатации и программированию

Поделиться
Скачать
Fire-Lite Alarms UDACT-F Скачать руководство пользователя страница 13

13

Document # 50049  Rev D   5/2/97  P/N 50049:D

Mounting Options
The UDACT-F may be mounted in the control panel or mounted
remotely in an ABS-8RF or UBS-1F enclosure up to 6000 feet away
from the control panel.  All power must be removed from the Control
Panel before making any connections to prevent circuit damage.  The
EIA-485 serial interface is connected between the Control Panel and
UDACT-F using twisted, shielded pair wire.  Power should be wired
from the Control Panel's 24VDC (nominal) filtered, nonresettable
output to TB1 on the UDACT-F (except when mounted in the MS-
9200).

2.2.1 MS-9200
The MS-9200 must have firmware with a Part Number of 73580 or higher installed to
allow use of the UDACT-F.  Remove all power from the MS-9200 by disconnecting
AC and batteries.  Install the supplied standoffs (three nylon and one aluminum standoff)
in the appropriate holes located on the right side of the MS-9200 main circuit board as
illustrated in Figure 2-2.  Position J10 located on the back of the UDACT-F over connector
J16 which is located center right on the main MS-9200 circuit board, and carefully
connect.  Secure the UDACT-F to the aluminum standoff with the screw provided.

The EIA-485 circuit and 24VDC power are provided directly from connector J16 of
the MS-9200.  Note: A 120 ohm EOL resistor is not required on the UDACT-F EIA-
485 terminals when it is installed inside the MS-9200 cabinet.  The EOL resistor is required
at the last device on the EIA-485 line external to the MS-9200 panel.

2.1                 General

                                   2.0   Installation

Figure 2-2: UDACT-F Mounting to MS-9200

Figure 2-1: ABS-8RF

2.2    Panel Mounting

MS-9200

3/4" aluminum standoff
with nut required for
transient protection

UDACT-F

3/4" Nylon
Standoffs

Technical Manuals Online! - http://www.tech-man.com

firealarmresources.com

Содержание UDACT-F

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды