Finn HydroSeeder T170 ML Скачать руководство пользователя страница 43

Страница: 43 / 95

Troubleshooting Chart

Symptom

Probable Cause

Suggested Solutions

VALVE

Valve stuck

Frozen

Thaw out ice and lubricate; leave
discharge valve in the open
position during storage.

Constant plugging
during operation

Foreign material in slurry.

Drain and clean out tank; check
sump area for foreign materials.

Constant plugging
during loading and
discharging

Loading HydroSeeder

before

tank is half full of water.

Reinstruct your operator. See
LOADING section.

Incorrect loading procedure.

See LOADING section.

Improper operation by
operator.

Reinstruct your operator. Review
OPERATOR’S MANUAL.

Clutch slipping.

Readjust clutch. See clutch
manual.

Restricted material flow by
partially closed valve.

Valve should be fully open.

Machine not being flushed out
prior to reloading.

See LOADING section.

Machine not being run at
correct RPM during loading.

Reinstruct your operator. See
LOADING section.

Extension hose plugs
after use

Letting water run out, leaving
wood fiber mulch to dry out.

If hose has to be uncoupled, seal
ends, to keep water in hose and
prevent wood fiber mulch from
drying out.

CLUTCH

Does not pull load or
overheats

Out of adjustment.

Readjust clutch. See clutch
manual.

Jumps out of
engagement

Too loose or too tight.

Readjust clutch. See clutch
manual.

PUMP

Excessive wear

Fertilizer with highly abrasive
fillers.

Change fertilizer – avoid abrasive
fillers.

Overloading machine with dry
material.

Load machine to recommended
capacities.

Too much time allowed
between loading and
discharging.

After loading and mixing has been
completed, set agitator at 1/4
speed in reverse and disengage
pump.

Recirculating all the time.

Close recirculation valve when
discharging through the boom.

Will not turn

Frozen

Warm housing to melt ice.

Jammed with fertilizer or lime.

Remove cover and clean interior.

Impeller rusted to suction
cover plate.

Pull cover and remove rust.

Содержание HydroSeeder T170 ML
































































































Результаты поиска

Содержание HydroSeeder T170 ML

Отзывы:

Похожие инструкции для HydroSeeder T170 ML

Бренды по названию

Популярные бренды

Finn HydroSeeder T170 ML, Инструкция оператора и каталог запасных частей

Результаты поиска

Содержание HydroSeeder T170 ML

Отзывы:

Похожие инструкции для HydroSeeder T170 ML

Бренды по названию

Популярные бренды