Finn HydroSeeder T170 ML Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 95

background image

15

MAIN MENU ACCESS

To access the Main Menu, press any of the three navigation buttons. The unit will display a
softkey popup window defining the available navigation possibilities. Select the Main Menu using
the center softkey as shown.

MAIN MENU NAVIGATION

Access the main menu using the center softkey. The main
menu will be displayed along with the main menu softkey popup
window. Navigate through the main menu selections by using
the “ ” key. When the desired menu item is highlighted, press
the “

” key to select the menu item. To exit the main menu and

return to the data displays press the EXIT “ ” softkey.

CHANGING PARAMETER SETTINGS

Parameter settings can be changed in one of two ways: using
the “

” / “

” softkeys to increase or decrease a numeric value

or using the Change “ ” softkey to toggle through a list of
programmed settings.

«
...
19
20
21
22
23
...
»

Содержание HydroSeeder T170 ML
































































































Отзывы:

Нет отзывов

Похожие инструкции для HydroSeeder T170 ML

Бренд: Abbott Страницы: 2

FreeStyle Libre

Бренд: Abbott Страницы: 3

Бренд: abc Страницы: 8

Бренд: Danfoss Страницы: 106

Бренд: XM Fitness Страницы: 10

Бренд: Nederman Страницы: 255

Бренд: Raymarine Страницы: 3

SmartPilot ST8002

Бренд: Raymarine Страницы: 48

Бренд: Raymarine Страницы: 38

hsb2 PLUS Series

Бренд: Raymarine Страницы: 248

Бренд: ValueStore US Страницы: 2

ULTRATHERM 908i

Бренд: gbo Страницы: 32

Бренд: Dantel Страницы: 6

Бренд: Zero 88 Страницы: 22

Бренд: Yaasa Страницы: 20

Бренд: Fast Страницы: 60

Бренд: GE Страницы: 18

Бренд: Kamar Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды