31
APPLICATION OF SLURRY (CONTINUED)
3. Application of wood and paper fiber: Whenever possible, aim the stream towards the
ground to create a surface with small pockmarks which will help get seed in contact with
ground. Do not allow the stream to blast away the surface of the seed bed.
4. Generally, the most remote area of the seed bed should be covered first. Distance is
controlled by engine speed and nozzle selection.
Do NOT partially close the boom discharge valve to control the
distance. Failure to comply could result in minor personal injury,
or product or property damage.
5. While moving along area to be seeded, the operator should move the nozzle back and
forth in a slow, even arc.
6. If application is to be interrupted for a short period of time, disengage (turn off) pump
clutch. If shutdown is going to be for an extended period of time (i.e., lunch break,
reloading, etc.), close the valves to prevent slurry from dewatering. Re-engage (turn on)
pump clutch to continue application.
7. It may be necessary to slow the agitator as the tank empties to reduce foaming.
II. DISCHARGE THROUGH THE BOOM
1. Move the discharge valve foot pedal to the
OPEN
position, the recirculation valve handle
to the
CLOSED
position, and engage (turn on) pump clutch. At this time, should the
operator want to stop spraying for a short period, disengage (turn off) pump clutch. When
ready to resume spraying, simply re-engage (turn on) the pump clutch.
2. When the tank is empty, or when discontinuing discharge for an extended period of time,
disengage (turn off) pump clutch, then immediately move the discharge valve to the
CLOSED
position, and idle the engine. This will maintain moisture in the discharge piping
and help prevent plugging. Move the agitator control to the
NEUTRAL
position.
III. PROCEDURES WHEN USING HOSES
Always pump clear water through the hose before pumping mulch. If the inside hose liner is dry, it
will dewater the mulch, causing the hose to plug.
A. PUMP TAKE-OFF SYSTEM OR HOSE REEL WITH REMOTE VALVE
1. Open recirculation valve, close discharge valve, and close remote valve at the end of the
hose.
2. Engage (turn on) the pump clutch. When stream is flowing freely through the recirculation
line, open the pump take-off valve.
The high pressure on the hose can exert strong forces, causing the
potential for the hose operator to lose control of hose or footing. The
hose will require additional hose holders when this operation occurs on slopes. Open the
pump take-off valve and the remote valve slowly and only after the hose operator is fi rmly
positioned and has fi rm control of hose. Failure to comply could result in minor personal
injury, or product or property damage.
3. With the engine running at approximately 3/4 speed, open the remote valve at the end of
the hose to discharge the load.
4. When finished spraying, close the remote valve, disengage (turn off) the pump clutch,
and stop the engine. If using fiber mulch, retain as much water as possible in the hose by
elevating the hose ends or by coupling the hose ends together.
Содержание HydroSeeder T170 ML
