Finn HydroSeeder T170 ML Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 95

background image

12

CONTROL PANEL GUIDE

NOTE:

This information is to explain the function and use of the control panel when starting the

unit.

DO NOT start the unit at this point. Refer to

STARTING PROCEDURE

section for

actual

operation.

SYSTEM POWER UP

The control panel is powered from the engine battery
connection from the engine harness connector. Make sure
the engine harness is connected to the control panel before
proceeding. Power up the system by turning the key switch
to the

ON

“

” position. This will activate the control panel

and apply power to the engine ECU.

If the control panel indicates a fault condition, DO NOT
start the engine. Review the fault condition and correct
the condition before starting the engine. See Fault Codes
section for details on system faults.

ENGINE START

To start the engine, turn the key switch clockwise to the

START

“

” position. If a fault condition

exists, the engine ECU may prevent the engine from starting. All fault conditions will be indicated
by the digital display. The display will indicate the active fault(s) by presenting a pop-up graphic
describing the fault condition.

ENGINE SPEED CONTROL (THROTTLE)

Once the engine is started, the control panel will set the engine speed to
the minimum RPM speed setting. To change the engine speed, toggle the
throttle control switch (“Fast-Rabbit / Slow-Turtle”) to the desired speed
setting. The engine speed cannot be set below the minimum RPM speed
setting or above the maximum RPM speed setting.

Pressing the throttle up or down increases or decreases the RPM by
10 RPM. If the throttle switch is held down in one direction for three
seconds, the RPM will ramp at a faster rate.

«
...
16
17
18
19
20
...
»

Содержание HydroSeeder T170 ML
































































































Отзывы:

Нет отзывов

Похожие инструкции для HydroSeeder T170 ML

Бренд: ICS Schneider Messtechnik Страницы: 124

Бренд: Tascam Страницы: 128

Бренд: ParaBody Страницы: 6

Бренд: IDEAL Networks Страницы: 60

Бренд: IceCure Страницы: 104

Бренд: Jasco Страницы: 2

Бренд: unios Страницы: 2

Бренд: Baileigh Industrial Страницы: 12

ZA top SM315.100A

Бренд: ZIEHL-ABEGG Страницы: 76

Бренд: VaBroom Страницы: 4

Бренд: Carbatec Страницы: 29

Бренд: PurAthletics Страницы: 2

Бренд: Econo-Wrap Страницы: 27

Бренд: Hatco Страницы: 40

Бренд: Grundig Страницы: 19

Бренд: Megger Страницы: 12

Бренд: Tecsis Страницы: 52

Бренд: Jäger Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды