Finn HydroSeeder T170 ML Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 95

background image

10

TWO-VALVE OPERATION

This HydroSeeder

®

is equipped with two

independently operated ball valves to control
slurry flow. One is located in the recirculation line
below the platform, and the other is located in the
discharge line above the platform.
The valve handles should be positioned as shown
in Figures 4 through 6 for the particular application
required.

Never engage (turn on)

slurry pump clutch when

both valve handles are positioned as shown in
Figure 4. Both valves are closed and will result in
extreme heat generation. Failure to comply could
result in severe personal injury or death.

1. DISCHARGE THROUGH BOOM:

Flow is through the boom with no flow through the
closed recirculation valve (Figure 5). Flow through
the boom is started and stopped by engaging or
disengaging the slurry pump clutch. The operator
controls the spray volume and flow by adjusting the
engine's RPMs.

2. EXTENSION HOSE THROUGH BOOM:

Flow is through the boom with no flow through the
closed recirculation valve (Figure 5). Flow through
the extension hose is started and stopped by
engaging or disengaging the slurry pump clutch.
The operator controls the spray volume and flow by
adjusting the engine's RPMs.

Do not use remote valve in this application. Failure to comply WILL

result in severe personal injury or death.

NOTE:

Do not use the discharge valve to control distance. Valve should be
completely open. Control the spray volume and spray distance by
adjusting the engine RPM.

DISCHARGE VALVE

(SHOWN CLOSED)

RECIRCULATION

VALVE

(SHOWN CLOSED)

TANK

Figure 4 – DO NOT Engage (Turn On)
Pump Clutch

TANK

CLOSED

OPEN

FLOW

Figure 5 – Discharge Through Boom

«
...
14
15
16
17
18
...
»

Содержание HydroSeeder T170 ML
































































































Отзывы:

Нет отзывов

Похожие инструкции для HydroSeeder T170 ML

Бренд: zipwake Страницы: 2

Бренд: zipwake Страницы: 2

Бренд: Keiser Страницы: 2

Бренд: ECA Страницы: 3

Бренд: Nautilus Страницы: 12

Бренд: Hach Страницы: 66

Бренд: Hach Страницы: 14

Бренд: Hach Страницы: 144

QuikChem 8500 2 Series

Бренд: Hach Страницы: 80

Бренд: Hach Страницы: 178

Бренд: Hach Страницы: 32

Бренд: hager Страницы: 4

Бренд: Tascam Страницы: 8

Бренд: Taylor-Wharton Страницы: 25

Бренд: i-CAT Страницы: 96

Бренд: OAKWORKS Страницы: 2

Бренд: Oakton Страницы: 2

Бренд: Oakton Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды