Finn HydroSeeder T170 ML Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 95

background image

30

PRIOR TO APPLICATION

1. Operator(s) should familiarize themselves with the area to be seeded and develop a plan

to ensure uniform application.

2. Develop a plan for communication between operator and driver of the carrying or towing

vehicle to signal for start, stop, turn, etc., through the use of the signal horn.

3. Operator takes up position on the platform. From this point, application will be controlled

by the use of the clutch, valve, discharge assembly, and throttle.

DISCHARGE NOZZLE SELECTION

Nozzles are stored in the tool box. This HydroSeeder

®

is equipped with six nozzles – two long distance and
four fan nozzles. The smaller, long-distance nozzle
is generally better suited for seed, fertilizer, and/or
lime application, while the large, long-distance nozzle
is better for wood fiber mulch application. All of the
fan nozzles are generally suited for both types of
application.

Nozzle

Part Number

Distance (A)

Width (B)

Discharge Time

Lg. Long Distance

008465

Up to 200 ft. (61 m)

-

7.5 min.

Sm. Long Distance

011703

Up to 150 ft. (46 m)

-

30 min.

Sm. Narrow Fan

011707

Up to 75 ft. (23 m)

15 ft. (4.6 m)

30 min.

Sm. Wide Fan

011706

Up to 45 ft. (14 m)

25 ft. (7.6 m)

30 min.

Lg. Narrow Fan

011891

Up to 90 ft. (28 m)

23 ft. (7 m)

10.6 min.

Lg. Wide Fan

011890

Up to 50 ft. (15 m)

35 ft. (10.5 m)

10.6 min.

APPLICATION OF SLURRY

I. GENERAL APPLICATION TECHNIQUES

Do not spray toward power lines, transformers or other

high voltage conductors. Failure to comply WILL result in

severe personal injury or death.

The driver of the carrying vehicle should remain alert for

hazards to the operator, such as low power lines, hanging

branches, etc. Driver should never start or stop abruptly. Failure to comply could result in
minor personal injury, or product or property damage.

1. Determine which nozzle would best suit the application needs according to the

DISCHARGE NOZZLE SELECTION table.

2. Application of seed, fertilizer, and lime: Elevate discharge nozzle no less than 10 degrees

above the area to be sprayed, allowing the slurry to gently rain onto the seed bed.

A

B

Figure 8 – Nozzle Spray Dimensions

«
...
34
35
36
37
38
...
»

Содержание HydroSeeder T170 ML
































































































Отзывы:

Нет отзывов

Похожие инструкции для HydroSeeder T170 ML

Бренд: Taurus Страницы: 28

Бренд: Kärcher Страницы: 54

Бренд: ABB Страницы: 85

Бренд: GE Страницы: 43

Бренд: GE Страницы: 37

Бренд: GE Страницы: 210

Бренд: GE Страницы: 160

Бренд: GE Страницы: 146

Бренд: GE Страницы: 6

Бренд: GE Страницы: 27

Бренд: GE Страницы: 4

Бренд: Ecco Страницы: 9

Бренд: Talet Equipment Страницы: 17

Бренд: MacDon Страницы: 272

Бренд: MacDon Страницы: 70

Бренд: Eagle Eye Страницы: 21

Бренд: Labomed Страницы: 67

Бренд: HABYS Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды