Finn HydroSeeder T170 ML Скачать руководство пользователя страница 15

Страница: 15 / 95

EQUIPMENT CHECK

Equipment check should be made with the engine OFF and all

rotating parts stopped. Failure to comply could result in severe

personal injury or death.

1. Make sure that tool kit contains all the prescribed items. See TOOL KIT list in parts

section.

2. Inspect the slurry tank for foreign objects. See numbers 2 and 3 in IV. MAINTENANCE of

the HYDROSEEDER

SAFETY SUMMARY SECTION.

3. Check fuel level and fill if necessary.

4. Check the hydraulic oil level and fill to proper level if necessary. See HYDRAULIC

SYSTEM for oil specifications.

5. Check engine oil level and fill to proper level if necessary. For oil type refer to the engine

manual.

6. Check fluid level in radiator and fill to proper level if necessary.

7. Inspect air cleaner for dust and dirt; clean or replace if necessary.

8. Secure the tank drain cap on the slurry tank drain pipe.

9. Check to be certain all pump drain plugs are in place.

10. Verify that the suction line shut-off valve is completely open.

11. Engage (turn on) and disengage (turn off) pump clutch to determine if it snaps in and out.

12. Check nozzle for obstructions and clean as required.

13. Check pump discharge and recirculation valve handles for free movement.

14. Make sure all tank vents are clean and open. Do not plug or cap.

15. Lubricate equipment - See LUBRICATION AND FLUIDS CHART.

A. Each lubrication point is marked.

B. Check automatic pressure lubricator at pump. If the stem

is fully extended with thumb nut all the way up, then
automatic pressure lubricator contains lubricant. If not,
lubricant must be replaced by the following procedure:

a) Turn thumb nut clockwise until stem rises to maximum

height.

b) Remove cap and fill cap with sodium-(water soluble)

base grease. (FINN part number 000698). Do not use
lithium-base (chassis lube) grease.

c) Replace cap.

d) Turn thumb nut counterclockwise until the thumb nut

is at the top of the stem. The spring and pressure disc
in the lubricator forces the grease, under pressure, to
the pump seal.

When the thumb nut has moved down to within 1/2 in. (1.25 cm) of

touching the cap, re-service the automatic pressure lubricator.

Figure 3 – Automatic
Pressure Lubricator

THUMB NUT

STEM

CAP

GREASE

PRESSURE

DISK

SPRING

Содержание HydroSeeder T170 ML
































































































Результаты поиска

Содержание HydroSeeder T170 ML

Отзывы:

Похожие инструкции для HydroSeeder T170 ML

Бренды по названию

Популярные бренды

Finn HydroSeeder T170 ML, Инструкция оператора и каталог запасных частей

Результаты поиска

Содержание HydroSeeder T170 ML

Отзывы:

Похожие инструкции для HydroSeeder T170 ML

Бренды по названию

Популярные бренды