Finn HydroSeeder T170 ML Скачать руководство пользователя страница 34

Страница: 34 / 95

LOADING AND MIXING BFM, FGM, SMM AND

OTHER HIGHLY VISCOUS SLURRIES

1. With pump clutch disengaged (turned off), agitator control in the NEUTRAL position and

hydraulic system off, start engine and allow it to warm up. See STARTING PROCEDURE.

2. After engine has warmed up, turn on the hydraulics system by flipping the hydraulics

toggle switch to the

HYDRAULICS ON

position (all the way up). The switch will

automatically center itself, which is the

position.

3. Start filling unit with water from one of the water sources as listed below. When water

reaches the top of agitator shaft, move agitator control to full REVERSE position.

Tank can be filled by using one of the sources of water as follows:

A. Water from any stream or pond using a fill pump. When filling from a pond or

stream, be sure to use a suction strainer to filter out contaminants that could
damage the pump and unit.

B. Any pressure source, e.g. fire hydrant. An optional air gap fill port is available for

this unit but it is necessary to consult with local authorities before using a water
main, in order to abide by all local ordinances.

C. Water tanker.

4. Piping System Cleanout Procedure:

A. Remove discharge nozzle and coupler gasket from the remote valve coupler at the

end of the discharge hose (or from boom on the platform option).

B. Aim discharge hose (or boom on the platform option) into an open area away from

any persons, obstructions, or high voltage power lines.

C. Open discharge and remote valves and close recirculation valve.

D. Engage (turn on) pump clutch with a firm snap. Do NOT allow clutch to slip.

E. Increase engine speed to approximately 1/2 to 3/4.

F. When discharge stream is clear, open recirculation valve and close discharge

valve. After recirculation stream is clear, disengage (turn off) pump clutch.

G. Replace coupler gasket in the remote valve coupler (or in boom on the platform

option).

5. Continue filling tank with water.

6. Increase engine speed to full RPM. Governed speed of the engine on the FINN

HydroSeeder® should be 2,500 RPM under load.

Содержание HydroSeeder T170 ML
































































































Результаты поиска

Содержание HydroSeeder T170 ML

Отзывы:

Похожие инструкции для HydroSeeder T170 ML

Бренды по названию

Популярные бренды

Finn HydroSeeder T170 ML, Инструкция оператора и каталог запасных частей

Результаты поиска

Содержание HydroSeeder T170 ML

Отзывы:

Похожие инструкции для HydroSeeder T170 ML

Бренды по названию

Популярные бренды