Finn HydroSeeder T170 ML Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 95

background image

32

APPLICATION OF SLURRY (CONTINUED)

5. If another load is to be done, see RELOADING PROCEDURE. If finished for the day,

follow the clean-up procedure and flush out the hose.

The recirculation valve must be open when using a remote valve.

Failure to comply will result in serious injury or death.

B. EXTENSION HOSE SYSTEM - WITHOUT REMOTE VALVE

1. Connect the extension hose into the end of the discharge boom.

2. A person controlling the end of the hose directs a second operator at the machine to

control the pump clutch and adjust the engine speed.

Since the extension hose will be seeing the full output of the pump

with the recirculation closed, the equipment operator and individual at

the end of the hose should exercise extreme care when operating the unit on high pressure.
The high pressure on the hose can exert strong forces, causing potential for the hose
operator to lose control of hose or footing. The hose will require additional hose holders
when operation occurs on slopes. Engage the pump clutch only after the hose operator
is fi rmly positioned and has fi rm control of hose. Failure to comply could result in minor
personal injury, or product or property damage.

3. When hose operator is ready, signal the second operator to engage pump clutch and

slowly increase the engine RPM until the desired discharge pressure is reached.

4. When finished spraying, disengage the pump clutch, stop the engine, and close the

discharge valve. If using fiber mulch, retain as much water as possible in the hose by
elevating the hose ends or by coupling the hose ends together.

5. If another load is to be done, see RELOADING PROCEDURE. If finished for the day,

follow clean-up procedure and flush out the hose.

RELOADING PROCEDURE

1. Start at step 2 in LOADING.

2. After last load of the day, refer to CLEANING AND MAINTENANCE section.

3. If the unit is equipped with an Air Flush System, refer to the Air Flush System Parts and

OPERATOR'S MANUAL.

«
...
36
37
38
39
40
...
»

Содержание HydroSeeder T170 ML
































































































Отзывы:

Нет отзывов

Похожие инструкции для HydroSeeder T170 ML

BELMONT 2001039

Бренд: Backyard Discovery Страницы: 50

Бренд: Backyard Discovery Страницы: 45

Бренд: Backyard Discovery Страницы: 70

Бренд: BACtrack Страницы: 16

Бренд: ParaBody Страницы: 6

Бренд: ParaBody Страницы: 11

Бренд: mychway Страницы: 56

Бренд: Cooper Lighting Страницы: 1

Бренд: Energetics Страницы: 89

Бренд: Transpak Страницы: 9

Бренд: Telecast Страницы: 16

Бренд: Dentsply Sirona Страницы: 2

Бренд: Qlight Страницы: 4

CZ Master Set Pro 3

Бренд: GemOro Страницы: 16

Бренд: Wacker Neuson Страницы: 78

Бренд: Ditch Witch Страницы: 133

Бренд: Scilogex Страницы: 12

Бренд: Eaton Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды