Finn HydroSeeder T170 ML Скачать руководство пользователя страница 32

Страница: 32 / 95

LOADING (FOR WOOD FIBER MULCH, IF LIMING SEE LIMING WITH

THE HYDROSEEDER

SECTION)

Keep hands and arms away from tank interior and agitator. Failure to

comply will result in serious injury or death.

Take care not to lose pens, lighters, etc. from shirt pockets, or drop

pieces of paper or plastic bags into the tank, as these might plug the

slurry system. Failure to comply could result in death or serious injury. Failure to comply
could also result in product or property damage.

1. With pump clutch disengaged (turned off) and agitator control in the

NEUTRAL

position, start engine and allow it to warm up. See STARTING PROCEDURE section.

2. After engine has warmed up, turn on the hydraulic system by flipping the hydraulic

toggle switch to the

HYDRAULICS ON

position (all the way up). The switch will

automatically center itself, which is the

position.

3. Start filling unit with water. When water reaches the top of the agitator shaft, move

agitator control to full

REVERSE

position.

Fill tank using one of the sources of water as follows:

A. Water from any stream or pond using a fill pump. When filling from a pond or

stream, be sure to use a suction strainer to filter out contaminants that could
damage the pump and unit.

B. Any pressure source, e.g. fire hydrant. This unit is supplied with a 6 in. (15.2cm) air

gap fill port. Consult with local authorities before using water main in order to abide
by all local ordinances.

C. Water tanker.

4. Piping System Cleanout Procedure (Purging Line):

A. Remove discharge nozzle and gasket from discharge boom.

B. Aim discharge boom assembly into an open area away from any persons,

obstructions, or high voltage power lines.

C. Open discharge valve and close recirculation valve.

D. Engage (turn on) pump clutch with a firm snap. Do NOT allow clutch to slip.

E. Increase engine speed to approximately 1/2 to 3/4.

F. When discharge stream is clear, flush out hose on reel (if applicable), open

recirculation valve, and close discharge valve. After recirculation stream is clear,
disengage (turn off) pump clutch.

G. Replace nozzle and gasket in discharge boom.

5. Continue filling tank with water.

6. Increase engine speed to full RPM. Governed speed of the engine on the FINN

HydroSeeder® should be 2,500 RPM under load.

Содержание HydroSeeder T170 ML
































































































Результаты поиска

Содержание HydroSeeder T170 ML

Отзывы:

Похожие инструкции для HydroSeeder T170 ML

Бренды по названию

Популярные бренды

Finn HydroSeeder T170 ML, Инструкция оператора и каталог запасных частей

Результаты поиска

Содержание HydroSeeder T170 ML

Отзывы:

Похожие инструкции для HydroSeeder T170 ML

Бренды по названию

Популярные бренды