Fimap IMx Скачать руководство пользователя страница 59

Страница: 59 / 94

5-59

5.13

Alarm Table (IMx B/BT only)

5.13.1

Alarms

Alarms of Overcurrent and Temperature

Id Alarm

Meaning

Solution

AL 1: Function
Amp. Brush

Brush Amperometric Protection

Check consumption of the brush motor. Detected high current
on brush motor.

AL 2: Function
Amp. Vacuum

Vacuum Amperometric Protec-
tion

Check consumption of the vacuum motor. Detected high cur-
rent on vacuum motor.

AL 3: Function
Power Broken

Damage of Power

Damage power of brush or vacuum: replace the main card.
This alarm could be shown also during the trailing of the ma-
chine.

AL 4: Function
Overcurrent

Output overcurrent on brush or
vacuum

Detect a shortcircuit on output brush motor or vacuum motor:
Check connections and motors.

AL 5: Function
Overtemperature

Thermal

protection

brush/vacuum

Overtemperature of brush/vacuum motor: check consump-
tion of motors.

Traction Alarms

Id Alarm

Meaning

Solution

AL 14: Traction
Lever pressed

Safety lever pressed before start-
ing

Detected safety microswitch pressed before starting : release
the safety lever.

AL 15: Traction
Overtemperature

Thermal protection on traction

Overtemperature on traction : check consumption of traction
motor (IMx BT).

AL 16: Traction
Power damage

Power of traction damage

Replace the main card. This alarm could be shown also during
the trailing of the machine. (IMx BT)

AL 17: Traction
Overcurrent

Traction Overcurrent

Detected a shortcircuit on the traction motor output: Check
connections and traction motor (IMx BT).

AL 18: Traction
Amp. Traction

Traction Amperometric protec-
tion

Check how the traction function is used. Detected too high
working current on traction motor (IMx BT).

General Alarms

Id Alarm

Meaning

Solution

AL 20: General
EEprom malfunction

Error reading internal memory

Replace the main card.

AL 21: General
Key

Error key sequence

Error on key signal: Check the key connection. Check, also,
the batteries connections and main card

AL 22: General
General Relay

Damage of general relay

Check the traction motor connections. If the connection are
OK, the general relay on the main card is damaged: replace
the main card. The same alarm is present also if power fuse is
damaged

AL 23: General
Overvoltage

Overvoltage

Detected a overvoltage on the main card. Check the batteries
connections.

AL 24: Traction
Battery connections

Battery not connected to the
main card

Check the traction motor, Detected high voltage on traction
motor (IMx BT)

AL 25: General
Control Card connec-
tion

No communication between con-
trol card and main card

Check the connections between control card and main card.

Содержание IMx































































































Результаты поиска

Содержание IMx

Отзывы:

Fimap IMx, Руководство по ремонту, Страница: 59 / 94

Результаты поиска

Содержание IMx

Отзывы: