FENDT MAN D 0836 LE страница 53 Скачать руководство пользователя | Manualshive

Страница: 53 / 144

background image

Fav 900

Engine / Cylinder head

Re-machining the valve seats

G

Repair

Fav 900 chassis number 23/3001and up

19.02.2001

2010

000011

G

a

3/3

Capitel

Docu-No.

Index

Date

Version

Page

Re-machining the valve seats

PM-Picturemodule

PM-Picturemodule

PM-Picturemodule

PMTAB_Picture

Observe specified seat angle.

PMTAB_Picture

Note:
When re-machining the valve seat inserts, only
the minimum of material should be removed.
Reference value will be value of valve recess.

If the cylinder head faces are re-machined (max.1
mm (.039")), it is necessary also to re-machine the
inserts in order to obtain the correct valve recess:
When fitting new valves and inserts, machine out
cylinder head to amount relative to the skimming
of the cylinder head face.

Having skimmed the cylinder head face and
machined the valve seat insert, the theoretical
valve seat may have become too deep in the
cylinder head or the seat surface may be too wide.

PMTAB_Picture

In this event the valve seat insert must be
replaced.

Always observe the correct value for valve recess.

«
...
51
52
53
54
55
...
»

Содержание MAN D 0836 LE

















































































































































Отзывы:

Нет отзывов

Похожие инструкции для MAN D 0836 LE

Бренд: Danfoss Страницы: 28

EC FSE 400 - SERVICE 2002 & 2003

Бренд: GAS GAS Страницы: 74

Бренд: Isuzu Страницы: 174

Бренд: Lenze Страницы: 64

Бренд: Zimmer Страницы: 40

Бренд: Danfoss Страницы: 77

LOMBARDINI 9 LD 625-2

Бренд: Kohler Страницы: 92

AstroTrack 21047

Бренд: ORION TELESCOPES & BINOCULARS Страницы: 2

AUTOMATE MT01-2101-069002

Бренд: rollease acmeda Страницы: 30

Бренд: Detroit Diesel Страницы: 40

Бренд: Detroit Diesel Страницы: 195

Бренд: MULTIPLEX modell Страницы: 11

Бренд: DLE Страницы: 4

Бренд: DLE Страницы: 24

Бренд: DANA Страницы: 3

Бренд: DANA Страницы: 3

Бренд: Ford Страницы: 46

Бренд: HKS Страницы: 49

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды