FENDT MAN D 0836 LE Скачать руководство пользователя страница 133

Страница: 133 / 144

Fav 900

Engine / Injection valves

Checking injection nozzles

Testing

Fav 900 chassis number 23/3001and up

05.02.2001

2712

000001

2/3

Capitel

Docu-No.

Index

Date

Version

Page

Checking injection nozzles

Nozzles meeting these three requirements may be used again.

PM-Picturemodule

PMTAB_Picture

Dismantling injection nozzle

With the inlet opening facing downwards, fit
nozzle holder and nozzle assembly into the
holding device and clamp unit into the vise.

Unsrew threaded union, remove nozzle body,
intermediate washer, pressure screw,
compression spring and adjusting washer.

Remove the pressure pipe from the vise.

PMTAB_Picture

Overhauling injection nozzles

using a small piece of wood and petroleum or
diesel fuel, clean interior of nozzle (1).

With a clean rag remove dirt from needle valve (2).
Coked up needle sections can be placed on a
lathe and cleaned with a soft wooden stick dipped
in oil.

Note:
To prevent corrosion, do not touch rectified
surfaces of the needle valve.
Needles and nozzles are paired and must not
be interchanged.

Check clean components for wear and damage ;
replace if necessary. Degrease all new parts.

PMTAB_Picture

Reassembling injection nozzle

Remove pressure pipe connector from the vise
and refit compression spring and adjusting
washer.

Содержание MAN D 0836 LE

















































































































































Результаты поиска

Содержание MAN D 0836 LE

Отзывы:

Бренды по названию

Популярные бренды

FENDT MAN D 0836 LE, Руководство по ремонту

Результаты поиска

Содержание MAN D 0836 LE

Отзывы:

Бренды по названию

Популярные бренды