FENDT MAN D 0836 LE Скачать руководство пользователя страница 59

Страница: 59 / 144

Fav 900

Engine /Cooling system

Removing and refitting water pump

Repair

Fav 900 chassis number 23/3001 and up

14.2.2001

2050

000003

2/4

Capitel

Docu-No.

Index

Date

Version

Page

Removing and refitting water pump

PM-Picturemodule

PMTAB_Picture

Refitting the water pump

Replace seals on connecting pipe.

Install water pump with new gasket.

Tighten fscrews to specified torque.

Put all removed parts back into place

Fill up coolant.

PMTAB_Picture

Overhauling the water pump.

1. Impeller

2. Sliding ring gasket.

3. Water pump bearing.

4. Pump housing.

5. Circlip

6. V-belt pulley

Remove water pump

PMTAB_Picture

Clamp water pump lift section in a vise (use
non-metallic jaws).

Remove V-belt pulley with pulling device.

Remove circlip from pump housing.

Invert water pump and fit into hydraulic press

Using a suitable mandrel (same as bearing shaft)
press out bearing.

Note:
When the bearing is pressed out, the pump
impeller is released.

PMTAB_Picture

Using a suitable mandrel, press out and replace
sliding ring gasket.

Reassambling the water pump

Using pressing bush (special tool) press in a new
sliding ring gasket as far as possible. See notes
on fitting gasket !

Содержание MAN D 0836 LE

















































































































































Результаты поиска

Содержание MAN D 0836 LE

Отзывы:

Бренды по названию

Популярные бренды

FENDT MAN D 0836 LE, Руководство по ремонту

Результаты поиска

Содержание MAN D 0836 LE

Отзывы:

Бренды по названию

Популярные бренды