FENDT MAN D 0836 LE страница 93 Скачать руководство пользователя

Страница: 93 / 144

Fav 900

Engine / Short block

Removing and refitting the crankshaft

Repair

Fav 900 chassis number 23/3001and up

20.2.2001

2210

000008

1/3

Capitel

Docu-No.

Index

Date

Version

Page

Removing and refitting the crankshaft

PM-Picturemodule

PMTAB_Picture

Removing and refitting the crankshaft

●

Remove oil pan, oil line and idler gear.

●

Remove timing case and flywheel housing.

●

Remove cylinder head.

●

Remove piston and con-rod.

PMTAB_Picture

Gradually loosen screws of crankshaft bearing
caps from the center outwards and remove: Take
off bearing caps and arrange in order of assembly.

Note:
Bearing cap positions in relation to the
crankcase are identified by numbers: bearing
number 1 is at the fan end.

Remove bearing shells from bearing caps. If they
have not been marked, identify bearing shells and
caps appropriately.

PMTAB_Picture

Remove the lower part of the axial stop washer.

PMTAB_Picture

Lift crankshaft out of crank case using a rope or
leather strap.

Note:
Do not use a steel cable as this could damage
the bearing faces of the crakshaft journals.

Remove bearing shells from crankcase.

If they have not been marked, identify bearing
shells and bearing caps appropriately.

Clean parts and check for wear; replace if
necessary.

Содержание MAN D 0836 LE

















































































































































Результаты поиска

Содержание MAN D 0836 LE

Отзывы:

Похожие инструкции для MAN D 0836 LE

Бренды по названию

Популярные бренды

FENDT MAN D 0836 LE, Руководство по ремонту

Результаты поиска

Содержание MAN D 0836 LE

Отзывы:

Похожие инструкции для MAN D 0836 LE

Бренды по названию

Популярные бренды