FENDT MAN D 0836 LE страница 54 Скачать руководство пользователя

Страница: 54 / 144

Fav 900

Engine / Cylinder head

Reseating valves

Repair

Fav 900 chassis number 23/3001 and up

19.02.2001

2010

000012

1/1

Capitel

Docu-No.

Index

Date

Version

Page

Reseating valves

PM-Picturemodule

PMTAB_Picture

Reseating valves

Apply grinding paste to the valve seating face.

Lubricate valve guide and insert valve.

With a valve grinding tool, regrind valve seat with
spinning movements.

Note:
Do not allow grinding paste to come into
contact with the valve stem and guide.

PMTAB_Picture

The re-grinding process of the valve seat must
produce a perfect, closed grinding pattern.

The width of the grinding pattern is the result of a
correctly machined valve seat insert.

1. Valve cone face

2. valve seat

PMTAB_Picture

1. Valve seat insert

2. Valve

3. Valve seat - too wide

4. Valve seat - correct

Note:
Excessively wide valve seats are favoring
carbon deposits,
- Valve may leak -
Excessively narrow valve seats prevent rapid
heat transfer from the valve to the cylinder
head.
- Valves become scorched-

Содержание MAN D 0836 LE

















































































































































Результаты поиска

Содержание MAN D 0836 LE

Отзывы:

Похожие инструкции для MAN D 0836 LE

Бренды по названию

Популярные бренды

FENDT MAN D 0836 LE, Руководство по ремонту

Результаты поиска

Содержание MAN D 0836 LE

Отзывы:

Похожие инструкции для MAN D 0836 LE

Бренды по названию

Популярные бренды