FENDT MAN D 0836 LE страница 31 Скачать руководство пользователя

Страница: 31 / 144

Fav 900

Engine / Cylinder head

Checking compression

Testing

Fav 900 chassis number 23/3001and up

20.2.2001

2010

000001

1/1

Capitel

Docu-No.

Index

Date

Version

Page

Checking compression

PM-Picturemodule

PMTAB_Picture

●

Warm up engine until coolant temperature

reaches 60 to 80

C (140 - 176

F).

●

Check valves clearance and adjust.

●

Remove all injectors and injector holders.

●

See values of compression in chapter "Service

Data".

Starting with the 1st cylinder, fit new seal and
tighten. Install test adaptor of compression
recorder with threaded union and tighten.

PMTAB_Picture

Screw compression recorder onto test adaptor
and insert test sheet.

Using the starter motor, turn engine until the
indicator no longer deflects.

Connect compression recorder with test adapter
to the other cylinders and proceed as above.

PMTAB_Picture

Depending on the design of the compression
recorder, the engine can also be cranked directly
from the compression recorder.

To do this, the starter has to be connected to the
appropriate electrical leads.

PMTAB_Picture

Compare data and remove compression recorder
and test adapter. Apply "Never Seeze" to contact
faces of injector holders.

Fit injector holder and injectors using a new seal.
Screw on union nut and tighten to specified
torque.

Re-connect injection and leak-oil lines.

Note:
The union nut can be tightened with an open
end wrench without removing the injection
pipe.

Содержание MAN D 0836 LE

















































































































































Результаты поиска

Содержание MAN D 0836 LE

Отзывы:

Похожие инструкции для MAN D 0836 LE

Бренды по названию

Популярные бренды

FENDT MAN D 0836 LE, Руководство по ремонту

Результаты поиска

Содержание MAN D 0836 LE

Отзывы:

Похожие инструкции для MAN D 0836 LE

Бренды по названию

Популярные бренды