manualshive.com logo in svg

FENDT MAN D 0836 LE, Руководство по ремонту

Поделиться
Скачать
FENDT MAN D 0836 LE Скачать руководство пользователя страница 28

Fav 900

Engine / General system

Turbocharger, troubleshooting

B

Faults

Fav 900 chassis number  23/3001 and up

15.2.2001

2000

000003

B

a

1/2

Capitel

Docu-No.

Index

Date

Version

Page

Turbocharger, troubleshooting

Text-module

Before replacing the turbocharger, check the following:

Excessive engine oil consumption, lack of power and abnormal intake or exhaust noises are a frequent
cause of unnecessary turbocharger replacement.
Examination of the allegedly defective parts by the manufacturer often shows the turbocharger to be in
perfectly good working order.
To avoid this situation, the following checks must be performed :

Text-module

Excessive oil consumption

Bullet-List

●

Check air filter contamination

●

Check intake pipe for restricted cross section (e.g. damage, dirt)

Either are possible causes for increased oil consumption due to the higher pressure.

Bullet-ist

●

Check turbocharger for external traces of oil

Excessive oil consumption of the turbocharger is due to bearing wear, quickly resulting in mechanical
damage.

Text-module

Lack of power

For satisfactory power, observe correct settings for:

Bullet-

●

start of fuel delivery

●

valves clearance

●

engine control (at full load)

●

exhaust brake (must open fully).

Bullet-List

Also check:

●

Cylinder compression

●

air filter contamination

●

intake system for restricted cross sections and leaks

●

exhaust system for damage and leaks.

If none of these checks reveal the cause of poor performance, the turbocharger has to be also checked
for:

Bullet-List

●

Coking of turbine impedes easy rotation. (Axial movement may realese coking.)

●

Dirt within compressor

●

Damage by foreign objects

●

Turbine wheel in contact with housing

Remove visible contamination of compresssor side and check bearing clearance.

Text-module

Note:
Do not damage the compressor fan wheel.

Bullet-List

Abnormal intake and exhaust noises

●

Check intake and exhaust system adjacent to the turbocharger assembly. Damaged gaskets must

be replaced (can mislead to failure diagnostic of turbocharger).

●

If this does not eliminate the abnormal noises, the turbocharger is to be replaced. (A turbocharger in

good condition does not generate noise!)

Text-module

Содержание MAN D 0836 LE

















































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды