FENDT MAN D 0836 LE страница 77 Скачать руководство пользователя | Manualshive

Страница: 77 / 144

background image

Fav 900

Engine / Short block

Removing and refitting air compressor

G

Repair

Fav 900 Chassis number 23/3001 and up

23.2.2001

2210

000013

G

a

4/5

Capitel

Docu-No.

Index

Date

Version

Page

Removing and refitting air compressor

PM-Picturemodule

PM-Picturemodule

PM-Picturemodule

PM-Picturemodule

PMTAB_Picture

Due to the slanting teeth cut of the drive gear, the
crankshaft will turn by approx 15

°

by placing the

compressor into the timing case. In final position,
the upper edge of the drive fork (1) must be in
position (4) - flush with the unmachined lowlaying
part (3) .

If this posiition cannot be reached, the
compressor must be removed and the crankshaft
must be turned consequently.

PMTAB_Picture

Place 4 screws and tighten them in such a
manner that the control eccentric can still be
moved.

Screw in the screws of the rear side.

Place eccentric into the marked position of the
compressor body.

Consult following pages for avoiding high wear by
narrow clearance and excessive noise by
excessive clearance, pinion clearance must be
precisely adjusted.

PMTAB_Picture

Tighten in 3 steps the rear screws at the
prescribed torque.

Connect coolant tubes.

Connect lubrication line, intake tube and
compressed air line.

Complete coolant and check oil level within the
engine.

Fit hydraulic pump or place the substitution cover.

Check all connections for leaks.

PMTAB_Picture

Check pinion clearance

Check can only be performed by completely
mounted Timing Gear drive and by cold engine.

●

Remove hydraulic pump or substitution cover.

«
...
75
76
77
78
79
...
»

Содержание MAN D 0836 LE

















































































































































Отзывы:

Нет отзывов

Похожие инструкции для MAN D 0836 LE

Бренд: FAAC Страницы: 28

Бренд: Paccar Страницы: 71

Бренд: Indmar Страницы: 94

Бренд: Man Страницы: 64

Бренд: Bosch Страницы: 20

Rexroth Hagglunds CA 10

Бренд: Bosch Страницы: 53

Бренд: Bosch Страницы: 60

Бренд: Bosch Страницы: 74

Rexroth Hagglunds CA 100

Бренд: Bosch Страницы: 76

Rexroth 70 Series

Бренд: Bosch Страницы: 56

Rexroth IndraDyn T

Бренд: Bosch Страницы: 76

Rexroth A10VER 52 Series

Бренд: Bosch Страницы: 56

Бренд: Bosch Страницы: 48

Бренд: Bosch Страницы: 114

Бренд: Bosch Страницы: 72

Rexroth A6VM series 71

Бренд: Bosch Страницы: 76

Rexroth Hagglunds VI 44 Series

Бренд: Bosch Страницы: 68

Rexroth IndraDyn S MS2N

Бренд: Bosch Страницы: 118

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды