Feasa 20-F страница 81 Скачать руководство пользователя

Страница: 81 / 132

FEASA LED ANALYSER
FUNCTIONAL VERSION

Sequence Capture Mode

Set/Put SequenceWait##(#)

- Set Sequence Wait Time

Transmit

Receive

setsequencewait##

putsequencewait##

setsequencewait###

putsequencewait###

OK
OK
OK
OK

Where:

represents the wait time in milliseconds (00 – 99 msec)

###

represents the wait time in milliseconds (000 – 999 msec)

Description

This command is used to set the

Wait

time between captures. The

Wait

time can be set to any

value in the range 000 – 999 milliseconds. This

Wait

time is set for all Fiber Channels enabled

by the

tSequencemode# or putSequencemode#

command.

PutSequencewait##, PutSequencewait###

commands are stored in RAM memory while

SetSequencewait##, SetSequencewait###

commands are stored in Flash memory.

Example:

The PC transmits

putsequencewait10

to the LED Analyser to instruct it to set the wait time

between captures to 10 msec. The LED Analyser will return a string

to the PC.

putsequencewait10

To determine what Wait Time between Sequence Captures is set to, use the command

getsequencewait###

It will return a time in milliseconds.

getsequencewait
005 ms

(5 milliseconds)

Back to Index

Содержание 20-F





































































































































Результаты поиска

Содержание 20-F

Отзывы:

Похожие инструкции для 20-F

Бренды по названию

Популярные бренды

Feasa 20-F, Руководство пользователя

Результаты поиска

Содержание 20-F

Отзывы:

Похожие инструкции для 20-F

Бренды по названию

Популярные бренды