Feasa 20-F страница 26 Скачать руководство пользователя

Страница: 26 / 132

FEASA LED ANALYSER
FUNCTIONAL VERSION

Get Data Mode

getHSI##

- Get Hue, Saturation and Intensity

Transmit

Receive

gethsi##

gethsiall

hhh.hh sss iiiii

Where:

represents the Fiber Number and is a number in the range 01 – 20.

all

represents the 20 Fibers in a Feasa 20F, or 3 Fibers in a 3F.

hhh.hh

represents the Hue (Colour) and is a number in the range 0.00 – 360.00.

sss

represents the Saturation (whiteness) and is a number in the range 0–100.

iiiii

represents the intensity value of the LED under fiber

. This 5-digit number is in the

range 00000 – 99999. 00000 represents no Intensity or under range(i.e. the LED is off) and
99999 will represent over range or the LED is too bright.

Description

This command instructs the LED Analyser to return the Hue, Saturation and Intensity data for

fiber ## (01-20) in format

hhh.hh sss iiiii

where

hhh.hh

represents the Hue(Colour),

sss

represents the Saturation(whiteness) and

iiiii

represents the intensity value of the LED under

Fiber ##.
This command should be preceded by a

capture

command to ensure valid LED data is stored

in the memory of the LED Analyser. The data for each LED can be read out one-at-the-time, in
any order using gethsi01. Note: it is important for the PC to use 01, 02, 03, etc to indicate

Fibers 1, 2 and 3, etc.

Alternatively use the

gethsiall

command to read back the LED data for all 20 leds in

one command.

Example:

The PC transmits

gethsi05

to the LED Analyser to instruct it to send the stored Colour and

Intensity data for the LED positioned under Fiber No 5. The LED Analyser will return a string

hhh.hh sss iiiii

to the PC.

gethsi05

123.47 098 06383

Back to Index

Содержание 20-F





































































































































Результаты поиска

Содержание 20-F

Отзывы:

Похожие инструкции для 20-F

Бренды по названию

Популярные бренды

Feasa 20-F, Руководство пользователя

Результаты поиска

Содержание 20-F

Отзывы:

Похожие инструкции для 20-F

Бренды по названию

Популярные бренды