Feasa 20-F страница 6 Скачать руководство пользователя

Страница: 6 / 132

FEASA LED ANALYSER
FUNCTIONAL VERSION

Introduction

The

Feasa

LED Analyser

is an instrument that tests the HSI (Hue, Saturation, Intensity),

RGB (Red, Green, Blue Colour content of a single LED), xyChromaticity, Dominant Wavelength

and cct Colour temperature of Light Emitting Diodes (LEDs) in a test process. An individual Led
Analyser can have up to 20

1mm flexible Fiber-Optic Light Guides which are mounted

individually over the LEDs to be tested.

The Feasa Led Analyser can be trained to read other Led Parameters like Absolute Intensity
and CIEXYZ in Luminous flux (lm), Luminous intensity (cd, mcd), Luminance (cd/m^2). It can

also be trained to interpret the data from an RGB Led. These outputs will require the use of the
Feasa Led Spectrometer.

Emitted Light from the LEDs is guided through these Fiber-Optic Light Guides to the Analyser

where the raw data is stored. The raw data can then be read out of the Analyser through the
Serial or USB Interfaces.

The USB Interface is 2.0 compatible.

The Serial Interface is a 3-Pin Connector with a 3 pin to 9 pin dtype cable (supplied)

compatible with the RS-232C ports on machines.

All Colours are derived from the three primary Colours, Red, Green and Blue (RGB). The RGB
values are used to identify different Colour LEDs.

The raw data from the Led under test is stored on the Led Analyser and output in different

formats as required through the USB and Serial interfaces.

Other options include 2,3,5,6,10.

Back to Index

Содержание 20-F





































































































































Результаты поиска

Содержание 20-F

Отзывы:

Похожие инструкции для 20-F

Бренды по названию

Популярные бренды

Feasa 20-F, Руководство пользователя

Результаты поиска

Содержание 20-F

Отзывы:

Похожие инструкции для 20-F

Бренды по названию

Популярные бренды