Feasa 20-F страница 79 Скачать руководство пользователя

Страница: 79 / 132

FEASA LED ANALYSER
FUNCTIONAL VERSION

Sequence Capture Mode

Set/Put SequenceChannel@@ -

Select sequence mode Fiber No.

Transmit

Receive

setsequencechannel@@

putsequencechannel@@

OK
OK

Where:

represents the Fiber and is a number in the range 01 -20.

Description

This command is used to set the Fiber number associated with the

Capture Sequence

command. The command

putSequencemode1

should be executed before this command.

In addition, the commands

putsequencecapture@@

putsequencewait##

and

putsequencenumber###

should be issued before this command.

The Analyser can store up to 9999 captures in memory when this mode is selected.

putsequencechannel@@

commands are stored in RAM memory while

setsequencechannel@@

commands are stored in Flash memory.

Example:

The PC transmits

putsequencechannel04

to the LED Analyser to instruct it to do sequence

capture on Fiber 04 only. The LED Analyser will return a string

to the PC.

putsequencechannel04

To determine which Fiber Number is set, use the command

getsequencechannel

It will

return a number in the range 01 to 20.

getsequencechannel
05

(Fiber Number 5)

Back to Index

Содержание 20-F





































































































































Результаты поиска

Содержание 20-F

Отзывы:

Похожие инструкции для 20-F

Бренды по названию

Популярные бренды

Feasa 20-F, Руководство пользователя

Результаты поиска

Содержание 20-F

Отзывы:

Похожие инструкции для 20-F

Бренды по названию

Популярные бренды