Feasa 20-F страница 50 Скачать руководство пользователя

Страница: 50 / 132

FEASA LED ANALYSER
FUNCTIONAL VERSION

Set Data Mode

set/putFACTOR##

- Set the Exposure Factor

Transmit

Receive

setfactor##

putfactor##

OK
OK

Where:

represents the Factor Number and is in the range 01 – 15 (default 01).

Description

This command allows the user to adjust the

Exposure Factor

for

all

Fibers.

This is useful when it is required to test very dim LED's. The Factory default setting is 01. The

value can be adjusted from 01 to 15. The exposure time will be increased when the factor is
increased which will lead to longer test times and higher Intensity readings, For Example.

Capture Range

Factor 01 / Intensity

Factor 05 / Intensity

Factor 10 / Intensity

Factor 15 / Intensity

C3 (High)

22ms / 23K

110ms / 50K

220ms / 64K

330ms / 72K

Try using the lowest capture range first (c1) before adjusting the Exposure Factor.

These set values are stored permanently in memory and can only be changed by using the

setfactor

command again, power on/off will NOT effect the set Factor.

The put values are stored in RAM memory and must be changed by using the

putfactor

command each time after Power On/Off.

The current value can be read out using the

getfactor

command.

Example:

Set the Factor Number for all Fibers to 05.

setfactor05

Example:

Set the Factor Number for all Fibers to 05.

putfactor05

Back to Index

Содержание 20-F





































































































































Результаты поиска

Содержание 20-F

Отзывы:

Похожие инструкции для 20-F

Бренды по названию

Популярные бренды

Feasa 20-F, Руководство пользователя

Результаты поиска

Содержание 20-F

Отзывы:

Похожие инструкции для 20-F

Бренды по названию

Популярные бренды