Feasa 20-F страница 57 Скачать руководство пользователя

Страница: 57 / 132

FEASA LED ANALYSER
FUNCTIONAL VERSION

User Calibration Mode

This is a manual procedure to calibrate the Led Analyser. However we recommend to use the

Feasa UserCal program provided on the CD. Each command is detailed in the section below.

UserCal Manual Procedure:

Select Calibration set

setcalibrationset## (00-50)

Reset Analyser to factory defaults:
-

resetusercal (Reset all parameters to Factory default)

Capture (auto, manual, pwm)

capture

Dominant Wavelength reading
-

getwavelength@@

Dominant Wavelength Correction Offset
-

setwavelengthoffset@@##

Relative Intensity Reading for Fiber @@

getintensity@@

Relative Intensity Correction Factor

setintgain@@###

CIE xy Reading for Fiber@@
-

getxy@@

CIE Correction Offsets
-

setxoffset@@± 0.###

setyoffset@@± 0.###

Absolute Intensity Reading for Fiber@@
-

getabsint@@

Absolute Intensity Correction Factor
-

setabsintmult@@1.00

(

set the multiplier to 1

)

capture

(

auto, manual, pwm

)

getabsint@@

(

get the absolute intensity using a multiplier of 1

)

i.iiiie±00

(

absolute intensity based on a multiplier of 1

)

Divide the

Desired Intensity

i.iiiie±00

(

result will be new multiplier m.mmmmmE±ee

)

setabsintmult@@m.mmmmmE

ee (

set the new multiplier to o/p the desired Absolute Int.

)

getabsint@@

(

get the absolute intensity using new multiplier

)

#.####e±##

(

Absolute Intensity in Scientific Notation Format

)

Set the user calibration date:

setcalibrationdatedd/mm/yyyy

Note1:

you can skip the adjustment of a particular parameter if you don't need it.

Note2:

if you require dominant wavelength and absolute intensity, make sure the wavelength correction is done first

as it affects the absolute intensity readings.

Back to Index

Содержание 20-F





































































































































Результаты поиска

Содержание 20-F

Отзывы:

Похожие инструкции для 20-F

Бренды по названию

Популярные бренды

Feasa 20-F, Руководство пользователя

Результаты поиска

Содержание 20-F

Отзывы:

Похожие инструкции для 20-F

Бренды по названию

Популярные бренды