Feasa 20-F Скачать руководство пользователя страница 110

Страница: 110 / 132

FEASA LED ANALYSER
FUNCTIONAL VERSION

Daisy Chain Mode

BusC#pwm@@ - Store PWM LED Data for a specific Range

Transmit

Receive

Busc#pwm

Busc#pwm@@

OK
OK

Where:

# represents the exposure Range 1 – 5.

represents an averaging factor in the range 1 - 15.

If the @@ digits are omitted then a default setting of 07 is used.

Description

This command allows the User to specify the

exposure range

and an

averaging factor

when testing PWM LED's. Select the

exposure range # (1-5) to match the

Intensity

of the

LED's.

The Analyser tests these LED's by taking a number of readings and averaging the

results. A larger Averaging factor will lead to more stable results but increased Test Times.
The

averaging factor

@@ is a number in the range 1-15. If this number is omitted from the

command the default value is 07.

This command instructs the LED Analyser to read and store the Colour and Intensity of all the

LED's positioned under the fibers. The data is stored until the power is removed or another

capture

command is issued. When completed the Analyser will transmit the character

the receive line to the transmitting device (i.e. the PC).

busc1pwm10

There are 5 manual capture ranges each with an intensity output range of 0 to
99,999. Feasa recommends that the UUT readings should be in the 55K to 85K range

for the best stability.

Back to Index

110

Содержание 20-F





































































































































Результаты поиска

Содержание 20-F

Отзывы:

Feasa 20-F, Руководство пользователя, Страница: 110 / 132

Результаты поиска

Содержание 20-F

Отзывы: