Feasa 20-F страница 18 Скачать руководство пользователя

Страница: 18 / 132

FEASA LED ANALYSER
FUNCTIONAL VERSION

Capture Commands

The Capture commands are used to capture the parameters (colour, saturation, intensity, xy,

uv, wavelength, cct) of the LED's to be tested and store the results in the memory of the
Analyser.

These results can be read out later using the

GET DATA

commands.

Commands are transmitted and received using ASCII characters and are

NOT case-sensitive

All commands must be terminated with a

<CR>

<LF>

character. All responses from the

Led Analyser are also terminated with <

> <

The

Terminal Program

supplied on the CD is used to send/receive commands to/from the

Analyser. This program is also available as a drop down box in the

User

program and the

Test

Software program.

The

Feasa

LED Analyser USER

Program is a graphical tool that can be used to send

commands and receive results from the Analyser. It allows one LED to be tested at a time.
This Program also allows a Terminal Window to be opened so that the User can type the

commands directly and send them to the Analyser. The responses from the Analyser can be
observed in the Window.

The

Feasa LED Analyser TEST

Program allows the User to test all the LED's together. Pass

and Fail limits can be set and results can be printed and logged.

Alternately, the User may generate a customised Program that sends commands and receives
data through the virtual USB Com Port or RS232 Serial Port.

Capture Times Static Leds

The Capture Time for each range is outlined on the following Table.

Range

Capture Time

Range 1 low

650ms

Range 2 medium

200ms

Range 3 high

22ms

Range 4 super

4ms

Range 5 ultra

2ms

Auto Range

350ms

Back to Index

Содержание 20-F





































































































































Результаты поиска

Содержание 20-F

Отзывы:

Похожие инструкции для 20-F

Бренды по названию

Популярные бренды

Feasa 20-F, Руководство пользователя

Результаты поиска

Содержание 20-F

Отзывы:

Похожие инструкции для 20-F

Бренды по названию

Популярные бренды