Feasa 20-F Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 132

Feasa 20-F Скачать руководство пользователя страница 14

FEASA LED ANALYSER
FUNCTIONAL VERSION

Setting Tolerance Limits for Colour and Intensity

The test procedure requires the user to set the Pass/Fail limits for Colour and Intensity for
each LED which then becomes the standard against which LEDs to be tested are compared.

The Pass/Fail limits for Colour are chosen, in conjunction with manufacturer’s specifications,
from measurements taken from a sample number of typical LEDs.

Because Hue is expressed as a single number it is more convenient to set the limits for the
colour in terms of their Hue value.

Sample Hue Pass/Fail Limits

LED

Minimum

Maximum

Red

0

2

Green

110

130

Blue

220

250

Amber

2

10

Yellow

80

110

Orange

10

20

The Saturation value must be taken into account when testing White LED's. The Saturation is

a value between 0% and 100%. A pure white will have a value close to 0% while a pure
colour will have a value close to 100%. The Pass/Fail limits for intensity are chosen from the

average intensity values from a number of sample LEDs.

Sample Intensity Pass/Fail Limits in Auto Mode

Relative

Intensity Value

Upper

Limit

Lower

Limit

Comments

125

150

100

This represents a Very Dim LED,

Recommend using Manual Capture Range

C1, C2 or C1PWM, C2PWM

20000

25000

16000

This represents an Average LED,

Recommend using Manual Capture Range,

C2, C3 or C2PWM, C3PWM

70000

85000

55000

This represents a Bright LED, Auto capture

use is OK but Manual Range C3, C4, C5 or

C3PWM, C4PWM, C5PWM would be

recommended.

Figure 5.

Note

:- the Relative Intensity Value will depend on the Range selected.

Note

:- Feasa recommends selecting a Capture Range to achieve Relative Intensity Reading of 55K to 85K for the best

results.

Back to Index

14

«
...
12
13
14
15
16
...
»

Содержание 20-F





































































































































Отзывы:

Нет отзывов