FDP EX-CPL, Руководство по установке

Страница: 10 / 91

Page 10 of 91
Rev. 4.20
- B1+ - B2+
- AUX +
FAULT - + (30Vdc) N L
Battery fuse AUX power supply fuse
AC-DC ADAPTOR
230Vac 30Vdc
Trimmer Vac fuse
Siren out2 fuse 24Vdc out1 fuse
Fault out3 fuse
+
-
+
-
12V 7,2Ah
12V 18Ah 12V 7,2Ah
12V 18Ah
FAULT + - (30Vdc)
-
1
B
+
1
B
S
H
I
-
1
A
+
1
A
-2
B
+
2
B
S
H
I
-2
A
+
2
A
-2
4
+
2
4
S
H
I
+
S
-
S
- +
FAULT
S
H
I
O
C
1
O
C
2
O
C
3
O
C
4
RL2 RL1
PS2
N L
LINE 230Vac
F1 F2 F3
F4 F5
F6
F1: F315mA L 250V
F2: F315mA L 250V
F3: F315mA L 250V
F4: F1,6A L 250V
F5: F1,6A L 250V
F6: T400mA L 250V
FUSES LIST
2.4 FIXING THE CONTAINER
The control panel weighs about 10Kg without batteries inside (one battery weighs about maximum 6.5Kg). The
control panel must be fixed on a vertical wall or adapted and on equivalent support; it does not have to only come
supported without an adequate fixation. For the fixation to the wall, to use first the central holes, then the two
holes low. In order to improve the traction on the implantation support, it is possible to use the two holes in the up
too, for a total of five points of implantation. For the implantation, to use of the lives of 6mm of greater diameter.
For the fixing, use at least 3 screws of 6mm of diameter or more and with an adequate dowel. In case reinforce
the surface if necessary.
WARNING: the procedures described in this manual must be only made accessible to qualified personnel.
2.4.1 Cable arrangement
Pay attention to the disposition 230Vac net cables and loops cables.
Watching frontally box the metallic opened, three rectangular openings on the bottom and three holes sluices pre-
cut on the top part, can be viewed.
Use the holes in the following way:
•
rectangular hole or circular hole in top at left:
to use for the cables connected to the clips at left (outputs) and at the centrum (data transfer);
•
circular hole in top at centrum:
to use for the cables connected to the clips at the centrum (data transfer);
•
rectangular hole or circular hole in top at right:
to use for the cables connected to the clips at right (loop);
•
rectangular hole in bottom at centrum:
to use for the cables connected to the clips in bottom (auxiliar output at 24Vdc) and that of the transformer
(230Vca);
It is advisable to arrange the cable in tidy mode, so as to diminish the eventual and remote interferences between
they and the control panel.
In particular it is advisable to avoid to make to pass under the card electronic cables of loop and power supply.
This operation, yet, is not necessary, in how much it control panel and the protocol of the data has been plans in
such mode to be immune at the disturbs and similar interferences.
2.4.2 Observation
In the connection between the control panel and the magneto-thermic power switch, it is reccomended to lock the
three-polar cable or the single power supply conductors in way that during the wiring there aren’t any mechanical
movements which may effect or weaken the connection itself.
The purpose of this pre-caution is to maintain in any case a electrical security condition.