manualshive.com logo in svg

Fayat DYNAPAC CC1400C, Инструкция по эксплуатации, Страница: 87 / 239

Поделиться
Скачать
Fayat DYNAPAC CC1400C Скачать руководство пользователя страница 87

Operation

4812164601_C.pdf

2023-01-05

Interlock

The roller is equipped with Interlock.

The diesel engine with switch off after 4 seconds if the
operator gets off the seat when going
forwards/backwards.

If the control is in neutral when the operator stands
up a buzzer will go on until the parking brake button
is activated.

If the parking brake remains inactive, the diesel engine
turns off after 4 seconds.

The engine does not stop if the parking brake
is activated.

The diesel engine will switch off immediately if for any
reason the forward/reverse lever is moved out of
neutral when the operator is not sitting down and the
parking brake button has not been activated.

Sit down for all operations!

Sit down for all operations!

1

Fig. Operator platform
 1. Switch for Sprinkler system, wheels

Sprinkler system, wheels

The switch on the floor (to the right) must be
press down to activate the sprinkler system
on the rear wheels.

The sprinkler system is enabled as long as the switch
is actuated.

Remove your foot from the switch to disable the
sprinkler system.

71

Содержание DYNAPAC CC1400C
















































































































































































































































Отзывы:

Нет отзывов