Fayat DYNAPAC CC1400C Скачать руководство пользователя страница 72

Страница: 72 / 239

Machine description

4812164601_C.pdf

2023-01-05

Working mode, Vibration

Fig. Working mode, Vibration both
drums, AVC selected

The different working modes are selected with the help
of the working mode button on the panel.

1. Optional asphalt temperature meter (see the
chapter asphalt temperature meter)

Symbols are shown in the menu

Working mode,

vibration

for forward and rear drums.

2. Compaction status (off/on) on front/rear drum

Press one of the buttons (7) on the far right of the
panel. The side menu (8) will then appear on the
display.

Fig. Working mode, Vibration both drums,
AVC selected

The lowermost button (7) activates AVC mode
(Automatic Vibration Control), activation lights the AVC
symbol (9).

Press the uppermost button (7) and the submenu is
displayed.

The lowermost button (7) on the panel is pressed,
AVC (9) is activated and the symbol in the bottom right
of the display lights.

Fig. Working mode - Vibration Off

Содержание DYNAPAC CC1400C
















































































































































































































































Результаты поиска

Содержание DYNAPAC CC1400C

Отзывы:

Fayat DYNAPAC CC1400C, Инструкция по эксплуатации, Страница: 72 / 239

Результаты поиска

Содержание DYNAPAC CC1400C

Отзывы: