Fayat DYNAPAC CC1400C Скачать руководство пользователя страница 174

Страница: 174 / 239

Maintenance - 500h

4812164601_C.pdf

2023-01-05

Fig. Engine compartment -
D1703-M-DI-E4B (Tier 4f / Stage V)
1. Pre-filter
2. Hose clamps
3. Fuel pump

D1703 / V2203-M (Stage IIIA)

The prefilter is located to the left of the fuel pump in
the engine compartment.

Loosen the hose clamps (2) using a screwdriver.

Remove the pre-filter (1) and hand in to a waste
disposal site. This is a disposable filter and
can not be cleaned.

Fit a new pre-filter and tighten the hose clamps.

Start the engine and check that the pre-filter is tight.

Fig. Engine compartment -
D1803 CR (Tier 4f / Stage V)
1. Pre-filter

D1803-CR (Tier 4f / Stage V) /
V2403-CR-E4B (Tier 4f) / V2403-CR-E5B (Stage V)

Unscrew the fuel filter (1) located on the right side of
the battery in the engine compartment.

Install a new fuel filter

Ensure good ventilation (air extraction) if the
diesel engine is run indoors. Risk of carbon
monoxide poisoning.

Fuel tank - Cleaning

Fig. Fuel tank
1. Fuel tank

It is easiest to clean the tank when it is almost empty.

Pump out any bottom sediment using a suitable
pump, such as an oil drain pump.
Save the oil in a container and dispose of it
in an approved manner.

Keep in mind fire risk when handling fuel.

The fuel tank is made of plastic (polyethylene)
and is recyclable.

158

Содержание DYNAPAC CC1400C
















































































































































































































































Результаты поиска

Содержание DYNAPAC CC1400C

Отзывы:

Fayat DYNAPAC CC1400C, Инструкция по эксплуатации, Страница: 174 / 239

Результаты поиска

Содержание DYNAPAC CC1400C

Отзывы: