Fayat DYNAPAC CC1400C Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 239

Fayat DYNAPAC CC1400C Скачать руководство пользователя страница 27

Special instructions

4812164601_C.pdf

2023-01-05

Special instructions

Standard lubricants and other recommended
oils and fluids

Before leaving the factory, the systems and
components are filled with the oils and fluids specified
in the lubricant specification. These are suitable for
ambient temperatures in the range -15°C to +40°C
(5°F - 105°F).

The maximum ambient temperature for
biodegradable hydraulic oil is +35°C (95°F).

The maximum ambient temperature for
biodegradable hydraulic oil is +35°C (95°F).

Higher ambient temperatures,
above +40°C (104°F)

For operation of the machine at higher ambient
temperatures, however m50°C (122°F), the
following recommendations apply:

The diesel engine can be run at this temperature using
normal oil. However, the following fluids must be used
for other components:

Hydraulic system - mineral oil Shell Tellus S2V100
or similar.

Lower ambient temperature - Freeze risk

Make sure that the watering system is empty/drained
of water (sprinkler, hoses, tank/s) or that anti-freeze
has been added, to prevent the system freezing.

Close the ball valve and draw up the anti-freeze liquid
through the filter. See the chapter dealing with
Sprinkler system.

Temperatures

The temperature limits apply to standard versions
of rollers.

Rollers equipped with additional equipment, such as
noise suppression, may need to be more carefully
monitored in the higher temperature ranges.

high pressure cleaning

Do not spray water directly onto electrical components
or the instrument panels.

Place a plastic bag over the fuel filler cap and secure
with a rubber band. This is to avoid high pressure
water entering the vent hole in the filler cap. This could
cause malfunctions, such as the blocking of filters.

11

«
...
25
26
27
28
29
...
»

Содержание DYNAPAC CC1400C
















































































































































































































































Отзывы:

Нет отзывов