Fayat DYNAPAC CC1400C Скачать руководство пользователя страница 222

Страница: 222 / 239

Maintenance, 3000h

4812164601_C.pdf

2023-01-05

Air cleaner
Check - Replacement of main filter

Replace the air cleaner's main filter when the
indicator shows red. The indicator is located on
the filter, or in its immediate vicinity.

Fig. Air cleaner
1. Clips
2. Cover
3. Main filter
4. Backup filter
5. Filter housing
6. Dust valve

Release the clips (1), pull off the cover (2),
and pull out the main filter (3).

Do not remove the backup filter (4).

Clean the air cleaner if necessary.
See section Air cleaner - Cleaning.

When replacing the main filter (3), insert a new filter
and refit the air cleaner in the reverse order.

Check the condition of the dust valve (6).
Replace if necessary.

When refitting the cover, make sure that the dust valve
is positioned downwards.

Air filter indicator - Resetting

Fig. Indicator
1. Button

The air filter indicator is located on the filter,
or in its immediate vicinity.

The air filter indicator must be reset after replacing
the air filter.

Press the "button" (1) on the top of the indicator
to reset.

206

Содержание DYNAPAC CC1400C
















































































































































































































































Результаты поиска

Содержание DYNAPAC CC1400C

Отзывы:

Fayat DYNAPAC CC1400C, Инструкция по эксплуатации, Страница: 222 / 239

Результаты поиска

Содержание DYNAPAC CC1400C

Отзывы: