manualshive.com logo in svg

Fayat DYNAPAC CC1400C, Инструкция по эксплуатации, Страница: 209 / 239

Поделиться
Скачать
Fayat DYNAPAC CC1400C Скачать руководство пользователя страница 209

Maintenance - 2000h

4812164601_C.pdf

2023-01-05

Emulsion tank - Draining

1

2

3

Fig. Pump system
1. Water pump
2. Hose clamps
3. Draining hose

The tank is drained by first opening the rear cover.

There is a water pump (1) on the right-hand side,
inside the cover. Loosen the drainage hose (3) located
on the adapter by loosening the hose clip (2).

Turn the drainage hose downward and outward, place
a container below this on the ground and let the water
drain out.

When cleaning the tank, see Water tank - Cleaning.

The Emulsions tank is made of plastic
(polyethylene), and is recyclable.

The Emulsions tank is made of plastic
(polyethylene), and is recyclable.

Remember that there is a risk of freezing during
the winter. Drain the tank, pump, filter and lines,
or mix antifreeze in the water.

Remember that there is a risk of freezing during
the winter. Drain the tank, pump, filter and lines,
or mix antifreeze in the water.

Water tank - Draining

1

Fig. Water tank
1. Drain plug

Remember that there is a risk of freezing during
the winter. Empty the tank, pump and lines.

Remember that there is a risk of freezing during
the winter. Empty the tank, pump and lines.

Remove the drain plug (1) and allow all the water to
run out. Wipe clean the drain plug and screw back in.

193

Содержание DYNAPAC CC1400C
















































































































































































































































Отзывы:

Нет отзывов