Fayat DYNAPAC CC1400C Скачать руководство пользователя страница 216

Страница: 216 / 239

Maintenance, 3000h

4812164601_C.pdf

2023-01-05

Engine oil and oil filter - Change

Fig. Engine compartment right side -
D1703-E3B (Stage IIIA)
1. Drain hose
2. Drain plug
3. Filler cap
4. Oil filter

Run the engine until it is warm before draining the oil .

Switch off the engine and push in
the emergency stop.

Take great care when draining fluids and oils.
Wear protective gloves and goggles.

Fig. Engine compartment, right side -
D1703-E4B (Tier 4f / Stage V)
1. Drainage hose
2. Drain plug
3. Filler cap
4. Oil filter

Place a receptacle that holds at least 12 liters (8 gal.)
under the drain plug (2).

Undo the oil filler cap (3), and undo the drain plug (2)
in the end of the drain hose (1). Let all the engine oil
flow out.

Deliver the drained oil to special waste handling.

Refer to the engine manual for detailed
instructions when changing oil and filters.

200

Содержание DYNAPAC CC1400C
















































































































































































































































Результаты поиска

Содержание DYNAPAC CC1400C

Отзывы:

Fayat DYNAPAC CC1400C, Инструкция по эксплуатации, Страница: 216 / 239

Результаты поиска

Содержание DYNAPAC CC1400C

Отзывы: